What is stucco patch

Save my name, email, and website in this browser for the next time I comment. DIY Repairs. Stucco Patch Material From Home Depot: Home Depot has a few different materials that are available to the public and carry a couple of products that other stores do not. Stucco Patch Material From Lowes: Lowes and Home Depot carry some of the same products, so I won't mention them here, but will focus on the other products instead. Phenopatch Premixed Stucco Patch:.

Product Specs At A Glance: Dries in about an hours time Can be used on both interior and exterior stucco better for interior IMO Premixed, so it is easy to apply Comes in 1 quart or 1 gallon sizes Sandable and paintable for easy color matching Application: This is applied with a small trowel or a putty knife, whichever is easier Excess material can be wiped off with a sponge or float and water. Rapid Set Stucco Mix:. DAP Stucco Patch:. Comes in a 25 lb. Application: Mix the bag of DAP Stucco Patch and water Mix in a bucket for best results, using a high speed drill and a compatible mixing attachment, or you can use a wheelbarrow Apply with a hawk and trowel or with a taping knife drywall tools.

LaHabra Color Patches:. Quikrete Base Coat:. Comes in 80 pound bags You only need to add water Fine masonry sand, which is handy for certain applications Used for scratch and brown coats Application: Add water and bag together Mix in a mixer, wheelbarrow or a bucket with a high speed drill Can be sprayed on or applied using a hawk and trowel.

Quikrete 1 Coat Base Fiber Reinforced :. I would recommend using this product for both three and one-coat stucco applications. Pack down the edges with a brick trowel.

Wait for the wet sheen to disappear, then trowel the patch smooth, just below the level of the existing stucco. Cover again with a plastic sheet. After three days, remove the plastic, mist the patch, and mix up a fresh batch of stucco, following the finish-coat recipe. Different textures require different techniques. To match this wall's original "dash" finish, DiSilva scooped small globs of wet mix onto his brick trowel, then flicked them against the wall until they were flush with the old surface.

Let the patch cure for a week before painting it and the rest of the wall. Under a coat of heavy-bodied acrylic elastomer, the patch is invisible. Cookie banner We use cookies and other tracking technologies to improve your browsing experience on our site, show personalized content and targeted ads, analyze site traffic, and understand where our audiences come from.

By choosing I Accept , you consent to our use of cookies and other tracking technologies. How to Repair Stucco. By Thomas Baker. Pinterest Email Pocket Flipboard.

Add the acrylic bonding agent, then stir in water, a little at a time, until the mix reaches the consistency of buttercream frosting. Too much water will make it loose and unworkable. Once water is added, the mix will stay usable for 30 to 90 minutes before it starts to harden. Watch The Weather Freezing temperatures can ruin wet stucco. Work Safely The alkalis in wet cement can cause burns.

Finish It Right No patch, no matter how expertly textured, will match the color of the old stucco around it. Step 3: Cover The Exposed Lath Photo by Reena Bammi Using a utility knife, trim a piece of grade-D builder's paper to fit tightly along the boundary where the old stucco meets the exposed wood lath. Step 4: Add Mesh Photo by Reena Bammi Place galvanized metal lath over the paper and trim it tight against the edge of the stucco.

Step 5: Mix The Stucco Photo by Reena Bammi Following the first-coat recipe, stir up a batch of stucco, using a wheelbarrow as a mixing bowl. Step 6: Sling It Photo by Reena Bammi Wet the edge of the old stucco so it won't suck moisture out of the patch and weaken the bond between old and new. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights. Measure content performance.

Develop and improve products. List of Partners vendors. Materials Masonry. By Juan Rodriguez. Juan Rodriguez is a former writer with The Balance who covered large-scale construction. He is an engineer with experience managing and overseeing large civil works construction. Learn about our editorial policies. Remove the Loose Stucco Remove all loose or otherwise damaged stucco in the repair area by tapping it with a hammer and a cold chisel. Add Building Paper Cut two pieces of grade D building paper to fit the patch area.

Install Metal Lath Cut a piece of galvanized metal mesh stucco lath, using metal snips. Mix the First Batch of Stucco Mix a batch of quick-setting repair stucco, following the manufacturer's directions, using a drill and mixing paddle or, for large quantities, a mortar mixer. Apply the Scratch Coat Spray the edges of stucco around the patch area with water to prevent premature drying of the new stucco.

Apply the Brown Coat Mix a batch of stucco for the second, or brown, coat. Apply the Final Coat Mix a batch of stucco for the final, or color, coat. Your Privacy Rights. At any time, you can update your settings through the "EU Privacy" link at the bottom of any page. These choices will be signaled globally to our partners and will not affect browsing data.